Troubleshooting Packet Loss on Ports and VXCs
When accessing any network, small units of data called packets are sent and received. When one or more of these packets fail to reach their intended destination, packet loss can manifest in the form of network disruption, slow service, or even total loss of network connectivity.
If you notice packet loss on a Port or VXCVirtual Cross Connect.
Direct Layer 2 Ethernet circuits providing private, flexible, and on-demand connections between any of the locations on the Megaport network., step through these troubleshooting actions to isolate the root cause.
You can verify Port or VXC status from the Megaport ONE Portal. On the Services page, find the service and mouse over its icon. A message displays the status of the service and the color of the icon indicates the service status.
|Check interface or CRCCyclic redundancy check.
A type of error detection code used to detect transmission errors in data. errors and packet drops on the device
|Interface statistics and logs can help identify which end of the cross connect is causing the fault, and the potential solution. For example, an increasing number of incoming errors on a network interface generally rules out that specific SFPSmall form pluggable.
A hot pluggable transceiver used in data communication and telecommunication networks to enable data transmission between two devices. and indicates a potential issue with other components of the cross connect.
|Verify the Tx and Rx optical levels on the device||Check the transmitted (Tx) and received (Rx) light levels. This health check enables you to validate physical connectivity. Considerations:
|Verify physical connections with the data center (reseat and replace SFP, clean and replace cables, loopback test)||Open a ticket with the data center to perform the following tests:
|Verify carrier circuit status (if any)||Some cross connects are set through one or multiple carrier network devices before reaching the Megaport network. Verify that the device interfaces in the cross connect path are free of errors and optic light readings are operating correctly.|
|Validate equipment performance||While troubleshooting, Megaport ONE does not have visibility or access outside the Megaport network. To verify that the cause of an issue is within the Megaport network, Megaport ONE Support requires customers to validate the performance of their equipment. This includes ensuring that the hardware specifications and limitations are compatible with Megaport ONE’s Technical Specifications, and monitoring the network traffic and the workload on the hardware to avoid congestion or degraded performance. To ensure that hardware and your network is operating as expected, we recommend that you validate the performance of the following:
|Perform tracerouteA diagnostic tool that examines how data moves through the internet to determine if a destination is reachable. (or other test) to locate the symptom||Traceroute is a network diagnostic tool that tracks in real-time the pathway taken by a packet on an IP network from source to destination, reporting the IP addresses of all the routers along the path. Traceroute also records the time taken for each hop the packet makes during its route to the destination.
Perform end-to-end traceroute testing
If the troubleshooting actions do not resolve your issue, contact support. Before requesting assistance, collect the following information.
- Troubleshooting results – Provide all the troubleshooting steps you have taken in detail. For example, if loops were placed, note their location and which direction they faced.
- Source IP address and destination IP address – The source IP address is the IP address of the host that sent the packet. The destination IP address is the IP address of the host that should receive the packet.
- High-level network diagram – Understanding how your network design is implemented and the connection into the Megaport network helps identify additional focus areas within the troubleshooting process. Provide a network diagram that includes all devices in the path; note each device’s involved IP addresses and VLANs.
- Ping test results – Provide the output of each ping test performed on the service. Provide all output tests if you have multiple services related to different products (for example, a Port or VXC).
- Traceroute results – Provide traceroute results, indicating which side of the connection initiated the test and which side was the destination. We recommend that you use the A-End and B-End information from your VXC.
When a field service technician is needed onsite at the data center, see Customer Field Services for details.